Innovation comes from the reality, and every innovation is a thinking and attempt to solve practical problems. The appearance of packer comes from "moving bricks". Why is the word "moving bricks" popular on the Internet? Because it is very realistic to reflect the problems of large amount of labor and low efficiency in the brick industry. The appearance of the packer is for the brick factory, which greatly liberates the labor force, improves the production efficiency, saves the production cost, and is no less than an "industrial revolution" for the brick industry.
Today, the importance of the baler in the brick factory, not to say, chuanglixiaobian mainly talk about the common problems and treatment methods of the baler and its maintenance.
1、 The belt won't hold
1. The belt doesn't pull, the wheel rotates, and the machine doesn't move.
Treatment method: take down the tightening wheel, check the teeth of the tightening wheel, if there is dust, clean the dust. If the tightening gear is damaged, replace the tightening gear.
2. The belt does not pull, the wheel rotates, and the machine moves forward.
Treatment: remove the lower gear plate, check the lower gear plate, if there is dust, clean the dust. If the lower tooth plate is damaged, replace the lower tooth plate. If the elasticity of No. 83 spring is not good, it is necessary to replace No. 83 spring (it is recommended to replace No. 83 spring frequently). If the rotation resistance of No. 50 is large, take it down to clean the dust (pay attention not to oil, it is easy to stick dust).
2、 Cassettes
Insert the 3 mm Allen key into the cylindrical head screw # 164 through the opening in the bottom plate, and turn it 10 full turns in the anti clockwise direction. Twist with a little force. Pull the flip lever.
3、 Poor adhesion
1. Standardize the correct method of using the machine;
2. Check the quality of pet tape.
4、 Packer maintenance
1. Daily cleaning of the baler: after using the machine every day, first remove the black side cover, then screw off the four screws on the side of the panel, back the panel cover a little, you can see the belt in front of the motor, and then use the non water pressurized air to blow away the visible dust. Take off the tightening wheel and clean it with a brush and toothbrush (never use iron brush).
2. Comprehensive maintenance of the baler: clean the baler once a month. Because the baler is mainly composed of mechanical parts, it is inevitable to enter a lot of dust when it is used. It will accumulate more and more every day and need to be cleaned. Otherwise, it will accelerate the damage of the machine parts. Therefore, regular cleaning is essential. First, remove the four screws of the black side cover on the left side and remove the side cover. Then take off the four screws on the side cover of the panel, and let the side cover of the panel back. You will see that there are two lines connected to the side cover of the panel. Once it goes up and down, take off the upper line first. After taking off, the side cover of the panel can be completely withdrawn.
You can take off the 202 # black connecting line after you step out. Then take down all the screws on the shell of the machine, and take apart the shell. When taking apart, pay attention to tighten the wire under the switch, and remove the wire. Pay attention to all the wired places, and do not break the wire. Then take down the three thick wires, one black wire and one white wire on the circuit board. Then take down the 103. There are two screws on the base of the motor and a screw under the friction plate. Then the motor can be taken down. After taking out the motor, you will see a belt with two wheels, one big and the other small. The small wheel is set on a shaft, and one end is notched. Take a spanner to fix the gap After that, take a three big hexagon spanner to cover the black screw on the other end of the shaft, and then you can screw the screw off. After that, you can take out the belt. There is a white three big hexagon screw on the motor, and there is a three big hexagon screw on the tool holder. If you screw it off, you can separate the front part of the motor. The disassembly process is complete.
The next step is cleaning. Cleaning is mainly about the parts of the motor. Pay attention not to get wet when cleaning, and clean them with diesel oil. After cleaning, remove the diesel oil and grease the bearing and gear. Then assemble. Phonetic screw must be tightened, you can choose to put screw glue. The housing screws don't need to be too tight. After assembly, the whole maintenance is completed.